A new range of woodgrain effect metal sheds from Australia, manufactured from high grade hot-dipped galvanised steel which is 20% thicker than the standard range. Hot Dipped Galvanised gives the best overall protection to steel. This is superior to the alternative electro-plating or electro galvanised method. These sheds are made with superb WOOD GRAIN FINISH WALLS, which blend beautifully into any garden setting.

The Oakdale Metal shed is available in 4 sizes: Apex roofed sizes 6x5, 8x6, 10x8 and a 6' x 4' Pent design. The Oakdale features a 6ft front with double sliding door sited in the 6ft width. This steel shed is rot and rodent proof, will not crack and will maintain lasting good looks unlike many wooden sheds. The Oakdale Woodgrain effect Steel Shed is much heavier and sturdier than almost all other 'thin clad' steel sheds. The gables are ventilated to help prevent condensation building up. A sturdy ramp makes entry to and exit from the shed easy - even with wheel barrows or lawn mowers. We are able to give one of the best guarantees around - a 15 year no rust perforation guarantee.

Specifications:

Footprint	Roof (WxL)	Base (WxL)	Door (WxH)	Ridge Height	Eaves Height
	183 x 154 cm	171 x144cm	69w x 170h cm	193cm	178cm
	245 x 185 cm	233 x 175cm	104w x 170h cm	198cm	178cm
	307 x 247 cm	295 x 237cm	138w x 170h cm	203cm	178cm

(Please note: all measurements are approximate. The Oakdale Range are made from metric measurements.)

Optional Accessories

Hilti Hammacrews: for safe anchoring of sheds to concrete or slab bases. Each kit contains the correct number of fasteners and a masonry drill bit.

Timber floor Kit: This timber floor kit is constructed from fully pressure treated timbers for long maintenance free life. The floor boards are constructed from 19mm thick half lapped timber, and are mounted onto 50mm x 25mm sawn bearers. Nails are provided for assembly of the kit, as well as screws and washers for securing the shed base rails to the top surface of the floor. The floor can then be secured down to a hard standing with brackets and screws, or onto level well drained land with timber pegs (neither supplied).

Foundation Kit: Grid system foundation which fits the shed base rail exactly. This can be sited onto a level well drained soil area and then flooded out with concrete for a smooth floor area. Insert a DPC layer under the frame first for maximum damp protection.

Skylight: A translucent roof sheet which completely replaces a full metal roof panel, and permits plenty of daylight to enter the shed interior, whilst preventing visual identification of items stored inside. The Skylight can only be fitted to Apex roofed metal sheds.

One piece corner shelf: Galvanised triangular shelf section, which fixes simply to the top of the mid wall brace of the shed. A simple and economic item which can be used in either, or both of the two rear corners of the shed.

Three piece corner shelf: Galvanised triangular corner shelves, complete with support rails and fittings. Simple fitting, and providing a good area of storage space within a small area, helping to safely store all those small items.

Single rear wall shelf: A strong height adjustable shelf section designed to fit across the full width of the rear of your chosen shed. Comes complete with all braces and fittings, and is covered by 12mm thick MDF shelving board. Provides spacious and secure shelving to increase the storage capacity of your shed.

Double rear wall shelf: Two strong height adjustable shelf sections designed to fit across the full width of the rear of your chosen shed. Comes complete with all braces and fittings, and are covered by 12mm thick MDF shelving board. Provides spacious and secure shelving to increase the storage capacity of your shed.

Window Kit: 3mm thick two piece sliding Acrylic window. Approximately 61.5cm x 33cm (width x height). Kit supplied complete with ready cut down wall panel to make fitting a simple task. Please Note: The Window Kit can be fitted to most of the Shed Baron Grandale Metal Sheds. Refer to the optional accessories to see whether it is available for this model.

Assembly Please Note: Your building must be firmly anchored to a concrete, flagstone or timber foundation to protect against any wind damage. We recommend a 7.5 - 10cm poured concrete pad or a well grouted flagstone base made to our published 'maximum base foundation' size. This should be constructed on well drained hardcore with a DPC layer inserted approximately 5cm below the top surface. The base should be higher than the surrounding area to permit drainage of rainwater.

Options:

	Hilti Hammerscrews: Fits through pre-drilled holes in the base rail. Fix by simply hammering on the head of the drive screw. Kit supplied with masonry drill bit.
	Timber floor kit: shown made up. Comprises fully impregnated half lapped boards and bearers. Nails for assembly, plus screws and washers to fix the shed base rail to the top surface of the floor are included. Pegs for securing to soil bases are not included.
	Long shelf support rails: these rails support the 12mm thick MDF board supplied. Fits to the rear wall of the shed, for spacious and secure shelving. Kit comprises parts for 2 levels of shelving
	Corner shelves: galvinised shelves and supports supplied in kits of one or three shelves. Simple fitting. Provides a good level of storage space to help organise all those smaller items.
	Openable Window: 3mm Styrene glazed sliding window. Can be fitted to any shed (except LOW 6x4 Pent). Approx. 615W x 330H mm. Kit supplied with cut down wall panel.
	Skylight: Translucent roof sheet available to permit daylight to the shed interior. Replaces one full width roof panel.

Please Note: Customers ordering in the following Postal Regions ONLY - please ring for delivery surcharge in the following postal regions ONLY: AB, BT, DD, FK, HS, IM, IV, KY, KW, PA, PH, ZE